- 12” 3-JAW CHUCK
- DRO PROS 2-AXIS DIGITAL READOUT
- ALORIS TOOL POST WITH HOLDERS
- COOLANT SYSTEM
- THREAD CHASING DIAL
- INCH/METRIC THREADING
- LIVE CENTER
- JACOBS DRILL CHUCK
- TAILSTOCK
- CHUCK SHIELD
- WORK LIGHT
-
EQUIPPED WITH: -
Equipped With: INCH & METRIC THREADING 14" 4 JAW CHUCK CHIP PAN Location: OH -
EQUIPPED WITH 10" 3-JAW CHUCK TAPER ATTACHMENT THREAD CHASING DIAL THREAD NOSE HEADSTOCK GENERAL MOTOR: 3 HP OVERALL SIZE: 80" LR X 40" FB X 64" H WEIGHT: 2,500 LBS ELECTRICS: 220 VOLTS, 3 PH, 60 CYC -
EQUIPPED WITH 10" 3-JAW CHUCK TAPER ATTACHMENT THREAD NOSE HEADSTOCK GENERAL MOTOR: 3 HP OVERALL SIZE: 80" LR X 40" FB X 64" H WEIGHT: 2,500 LBS ELECTRICS: 220 VOLTS, 3 PH, 60 CYC -
Equipped With: 12" 3-Jaw Chuck Coolant System Tailstock Hardened and Ground Ways Inch and Metric Threading Location: TX -
NEW: 1978 EQUIPPED WITH: - INCH/METRIC THREADING CAPABILITY - 12" 4-JAW CHUCK - 9-3/4" 3-JAW - STEADY REST - FACEPLATE - THREAD DIAL INDICATOR - COOLANT SYSTEM - 7.5 HORSE POWER SPINDLE DRIVE MOTOR -
EQUIPPED WITH: Mitutoyo 2 Axis Digital Readout System, Model KA12 Counter 10" 3 Jaw Chuck with 2 Piece Jaws with Hard Reversible Top Jaws, 2" Thru Hole & D6 Mount Aloris Quick Change Tool Post with (11) Assorted Tool Holders (1) Live Center #4 Morse Taper (5) Adjustable Carriage Feed Kick Out Stops Swing Up Plexiglass Chuck Guard Spindle Jog Coolant On – Off Coolant System Built Into Base of Machine One Shot Carriage & Way Lubrication System Thread Chasing Dial Cross Slide and Compound Dials are Graduated in Inch & Metric 10-1/2" Steady Rest with Roller Supports Hardened Ground Bed Ways in Very Good Condition OEM Service Manual Complete Set of End Quadrant Change Gears Full Length Foot Treadle Spindle Brake Full Length Rear Splash Guard Main Drive Motor: 7-1/2 HP Coolant Pump Motor: 1/8 HP -
EQUIPPED WITH: 10" Bison 3-Jaw Set Tru Chuck with 2-Piece Hard Jaws Taper Attachment 2-Axis Newall Digital Readout, Model C80 7" Plain Steady Rest Headstock Reducer Sleeve to #6 Morse Taper Coolant System with Piping Halogen Work Light One Shot Carriage Lubrication System Full Length Foot Pedal Spindle Break Thread Chasing Dial (3) Adjustable Carriage Feed Stops (1) Follower Rest EQUIPPED WITH: Continued (1) Chuck Wrench (1) Camlock Wrench (1) Jacobs Key Type Drill Chuck, 0-1/2" Capacity with #4 Morse Taper Full Length Rear Splash Guard Inch Graduated Dials on Carriage Inch / Metric Dials on Cross Slide and Compound Axis Hardened and Ground Bed Way in Very Good Condition 7-1/2 HP Main Motor Wired for 3 Phase, 60 Hz, 230 / 460 Volts Presently Wired For 460 Volts -
EQUIPPED WITH:- 12" 3-JAW CHUCK
- ALORIS QUICK CHANGE TOOL POST WITH HOLDERS
- 5” STEADY REST
- 5 POSITION LONGITUDINAL STOP
- LIVE CENTER
- DRILL CHUCK
- COOLANT SYSTEM
- INCH/METRIC THREADING
-
EQUIPPED WITH:- Accurite Digital Readouts
- 16" 4 Jaw Chuck
- Steady Rest
- Tail Stock
- 10" 3 jaw chuck, 12" 4 jaw chuck
-
EQUIPPED WITH:- 10” 3 JAW CHUCK
- 10” 4 JAW CHUCK
- 15” FACE PLATE
-
EQUIPPED WITH:- 15” CHUCK 4 JAW
- 2” SPINDLE HOLE
- INCH/METRIC THREADING
- 15” SWING OVER CROSS SLIDE
- RAPID TRAVERSE
- 4 WAY TOOL HOLDER
- COOLANT
-
EQUIPPED WITH:- 4-Way Tooling
- 30" 4-Jaw Chuck
- 24" 3-Jaw Chuck
-
EQUIPPED WITH:- Newall Digital Readout
- Includes tailstock (not in picture)
-
EQUIPPED WITH:- INCH/METRIC THREADING
- 8" 3-JAW CHUCK
- TAILSTOCK
- CHUCK GUARD
- COOLANT SYSTEM
- FOOT BRAKE
- THREAD CHASING DIAL
- WORK LIGHT
-
EQUIPPED WITH:- 2-Axis DRO
- Steady Rest
- Taper Attachment
- 8" 3-Jaw Chuck
-
EQUIPPED WITH:- 14" 4 JAW CHUCK
- 9" STEADY REST
- COOLANT
- CHIP PAN
- TAIL STOCK
- 5 HP MAIN MOTOR
-
EQUIPPED WITH:- 4- Jaw Chuck
- Steady Rest
- Inch/Metric Threading
- Toolpost
- Chip Pans
-
EQUIPPED WITH:- ACCURITE III 2 AXIS DIGITAL READOUT
- 20" 3 JAW CHUCK
- 16" 3 JAW CHUCK
- 3 POINT ROLLER STEADY REST
- QUICK CHANGE TOOL POST
- 4 WAY RAPID TRAVERSE
- CHIP PAN BED
- COOLANT PUMP
- THREAD DIAL
- TRI-VEE BED DESIGN