-
EQUIPPED WITH: ADJUSTABLE RAKE ANGLE FRONT OPERATED POWER BACK GAUGE FOOT SWITCH BALL TRANSFERS ELECTRICAL: 460V/3PH/60HZ MOTOR: 20 HP
-
Year: 1988 EQUIPPED WITH: 48" CNC BACKGAUGE 12' SQUARING ARM ELECTRIC FOOT SWITCH CONTROL WEIGHT: 28,600 LBS
-
EQUIPPED WITH: Audemi PGP-401 Touch-N-Go Back Gauge Control 48" Back Gauge Sheet Support System 10' Squaring Arm Location: CA
-
EQUIPPED WITH: Front Operated Powered Back Gauge Ball Transfer Table Electric Foot Pedal 20 Horsepower Location: CA
-
Equipped With: 36" FRONT OPERATED POWERED BACK GAUGE 2 FRONT ARM SUPPORTS FRONT OPERATED MANUAL RAKE CONTROL.(.002"-.026") FORWARD / REVERSE SINGLE / JOG AND CONTINUOUS MODES 1" x 3" KNIVES Location: OH
-
Model: 837512 Year: 1992 Equipped With: Back Gauge with Digital Display Automatic Swing Up Back Gauge at 36" Shadow Light Squaring Arm 8' Foot Switch Manual Blade Gap Adjustment
-
MODEL #: M-2560 11 HOLD DOWNS 39.8' SQUARING ARM 2 FRONT ARM SUPPORTS 37" CNC 2 SPEED POWERED BACK GAUGE LIGHT BEAM SHEARING 3 PROBES IN BACK GAUGE FOR CONTACT SHEARING GOOD CONDITION
-
MODEL #: GHOE-630 36" FRONT OPERATED BACK GAUGE 13 HOLD DOWN ARMS SHADOW LIGHTING 43" SQUARING ARM FOOT PEDAL GOOD CONDITION
-
Year 1986 MODEL #: 300 G 16
-
Model - HDS Year - 1995
-
Series No. 612
-
Year: 1971 Model: 1812 Includes: 36" Power Operated Back Gauge Squaring Arm (3) Front Support Arm Electric Foot Switch 6" Slot in floor (Pit) required Excellent Condition Note - This machine was manufactured with a reduce rake angle to minimize distortion for narrow strips of thin material
-
(New 1979) 20' x 5/8" capacity 60" front operated power backgage 12' squaring arm LH side ball transfer table with power feed rolls & controls.
-
Save time and money by combining notching, beading, crimping and rolling in one operation. For complete round starting collars 3 to 14 inches in diameter out of 24-30 gauge galvanized steel, the Lockformer Collar Maker is the perfect tool. All it takes is one pass! Just cut to width and length or use scrap. This machine uses either 3" or 6" width blanks with simple movement of the crimp roll.
-
Brand New Machine Model 52 H Includes: Rear Manual Back Gauge Two Front Support Arms
-
New Primeline Hydraulic Shear Model 10H250 FEATURES: Swing-beam design with streamline appearance All steel frame, featuring box-type welded construction of the main frame and blade beam, with dimensions optimized by computer-assisted design to guarantee maximum rigidity Accurate upper blade beam guiding system Swivel-mounted hydraulic cylinders for maximum durability. Hydraulic unit located for convenient and easy access High-pressure hydraulic holddowns Low rake-angle of upper blade (minimizing distortion of narrow cut-offs) Rapid, single-point blade-clearance (blade-gap) adjustment device Easy blade re-setting Slow-stroking device (inching) to check blade clearance Easy adjustment of cutting length for shortening stroke when desirable for cutting narrow materials. When the stroke is shortened, the number of strokes per minute increases proportionately. Elgo go-to control with 200 steps of memory Deep gap (throat) to allow shearing of plates longer than the length of the blades, using slitting technique Double-acting cylinders for return of blade beam Ball transfers in machine table Little maintenance required as there are very few moving parts, the main ones being self-lubricated Rear bottom side of shear completely open for addition of stacking and conveying devices Light beam shearing gauge Jack bolts in machine frame for blade adjustment after sharpening, eliminating the need for shims Low voltage at the controls Note: Current delivery is 18-20 weeks - 35% deposit with order - Then balance due prior to shipment from factory.
-
Year: 1972 Model: 500 R 12 Capacity 12' x 1/2" Mild Steel 12'3" Between Housings Power Back Gauge Squaring Arm In Plant Under Power A rigger will need to be hired to load this machine at the buyers expense.
-
Year: 2002 Model: M1/4-10 Piranha 1/4” x 10’ Shear Power Operated front reading back gauge 3’, 4’ squaring arm, front arm supports Wired 440 Volt
-
Year: 1997 Model: 500HS X 12 Equipped with: 48" front operated programable backgauge with swing away backstop Allen Bradley PLC control Squaring bar mounted to table Ball transfers in table Hand clearance pockets in table T-slot in front of bed Manual blade gap in table Oil cooler Portable foot pedal Manual, Inch, single stroke, and automatic modes Light curtains
-
-
EQUIPPED WITH:
- 36” Front operated power backgauge
- Stroke control
- 36” squaring arm
- Ball transfers in table
- Portable Foot Pedal
- Inch & single stroke mode
- 4 hand clearance pockets
- Full length t-slots in front of tabe
- 4 T-slots F-B in table
- Gap adjustment in bed
- One shot lube system
-
EQUIPPED WITH:
- 8’ squaring arm
- Material drop support chute
- Ball transfers in table
- Quick change blade gap adjustment
- Stroke counter 48”
- Front Operated Programmable Backgauge with readout
- Pressure sensing holddowns
- Electric stroke adjustment Shadow light
-
EQUIPPED WITH:
- 36" Power Operated Back Gauge w/ LED Readout
- Electric Foot Switch
- New Set of Shear Blades
-
EQUIPPED WITH: NEW DRO FOR BACKGAUGE ELECTRICAL CONTROLS ELECTRIC FOOT PEDALS SHIPS FROM: TN
-
EQUIPPED WITH:
- FRONT OPERATED POWER BACKGUAGE
- FLOOR STANDING
- FOOT PEDAL