• EQUIPPED WITH:
    • UNIST Blade lubrication system
    • 10’ DoAll Factory roller table
    • Dual Swivel / Miter Head -45° / +60°
    • Hydraulic vise (Can be positioned in front or rear)
    • Front material table
    • Coolant pump
    • 2 H.P. Hydraulic pump
    • 5 H.P. Band saw motor
    SHIPS FROM: FL
  • Equipped With: INCH & METRIC THREADING 14" 4 JAW CHUCK CHIP PAN Location:  OH
  • Equipped With: 21 Tool ATC, Fadal CNC 32MP Control, Spindle Chiller, High Speed CPU, Graphics, CAT-40 Taper, Rigid Tapping and all available manuals Very Clean Well Maintained 40 X 20 with CNC 32MP Control, , 4th Axis Pre-Wire and 1,000BTS Location:  IL
  • Equipped With: 21 Tool ATC, Fadal CNC 32MP Control, Spindle Chiller, High Speed CPU, Graphics, CAT-40 Taper, Rigid Tapping and all available manuals Very Clean Well Maintained 60 x 30 with CNC 32MP Control, , 4th Axis Pre-Wire and 1,000BTS Location:  IL
  • MODEL HSM14 FOR CUTTING ALUMINUM AND OTHER NON-FERROUS MATERIAL WITH STEEL BLADE. 14" high speed mitre. 5HP TEFC, 3PH motor with magnetic starter, 3450 RPM. Please specify voltage. For non-ferrous only. Wt.750 lbs. Optional: 1,725 RPM motor. FOB:  MI
  • Model US10375 Includes: 36" Power Operated Back Gauge w/ LED Readout 39" Squaring Arm Ball Transfers on Each Table Segment Manual Quick Change Blade Gap High Carbon, Hi Chrome Shear Blades FOB:  TX
  • Model 3RSP 180/6 Standard Equipment: Hydraulically powered rear bending roll adjustment Electronic digital readout for rear bending roll position Hydraulic drop end Powered lower roll adjustment, with rapid gap adjustment Dual rotation controls - console mounted and remote hand control on trailing lead Upper and lower pinch rolls driven Cone bending attachment Powered tilting of the rear bending roll for cone bending Emergency stop cable at front and rear of machine Hydraulic oil, tools and manual Grooves in lower rolls for 1/4", 3/8", 1/2" FOB: Maryland  
  • MODEL HS1414 high-speed “straight-cut" non-ferrous saw. 5 HP, 3 PH 220 or 440 volt. Motor RPM 3450. Optional: 1,725 RPM motor. Wt. 250 lbs. Optional: 1,725 RPM motor. FOB: MI
  • MODEL KM10HS 10" high speed non-ferrous mitre saw. 3 HP TEFC, 3 PH 220/440V (please specify voltage) or 3 HP 1 PH 220V. Manual switch. Wt. 300 lbs. Dimensions L 25 x W 24 x H 17. LESS BLADE. FOB: MI
  • ~Additional state sales tax may apply~ Item Number BSV-20VS 2 hp motor runs on 220-volt single-phase power. Wide 20.5" throat depth. 12.375” maximum cutting thickness. Accepts standard .25” to .75” blades. Cast iron table can pivot front to back and left to right. Includes a cast iron mitering system, rip fence, and protractor to make sure your cuts are straight and repeatable. Variable speed from 65 to 1640 fpm allows you to adjust the speed for cutting wood, metal, and even plastic. Change the speed with the hand wheel (just turn right for higher speed, left for lower). Digital readout lets you see the exact blade speed, so you can choose the right settings for your material and extend blade life. This band saw includes everything you need to cut out the center of the material without having to fix a cut through it. Manual shear lets you cut the blade, so you can run it through the workpiece, then weld it back together. Comes standard with a fully-integrated blade welder with a built-in grinder for finishing the weld joint—great for getting to the center of a cut or repairing blades. Thick steel plate framework minimizes vibrations to deliver accurate cuts and helps the machine last for many years. Air blowdown system cools the blade and keeps the saw clean from material chips and shavings. Halogen work light lets you see what you’re cutting more clearly.  
  • Updated tonnage control Upgraded solenoid valve and calibrated the leveling system Rebuilt pumps Updated depth stop Equipped with: 5 speed ram Portable palm buttons Tonnage control Die holder Hardened ram inserts Depth stop with 5 digit readout Full length t-slot in front of bed Location:  MI
  • 10" high speed non-ferrous saw. 3 HP TEFC, 3 PH 220/440V (please specify voltage) or 3 HP 1 PH 220V.
    • Capacities: 3.25″ diameter solid.
    • 3450 RPM at spindle.
    • 5/8″ spindle arbor.
    • Sealed ball bearings.
    • Manual switch.
    • V-belt driven.
    • Uses a high speed carbide tipped blade (not included).
    • Single quick release cam-lock vise.
    • OSHA safety clam shell blade guard.
  • Model: S460HV • 4″ x 60″ belt • 1 HP, 1 PH, or 3 PH • 4″ pulley, 3450 RPM, 3600 SFPM, Direct drive • Reversible platen 4″ x 17″ • Cast iron table 4″ x 6″ • Full OSHA guard, Easy tracking , Quick belt change ! • DCV-6 Vacuum base 400 CFM • Dimensions: L 18″ x W 26″ x H 60″, WT. 485 lbs. • Manual switch – please specify phase and voltage
  • Model: S460W 4″ x60″ belt, 3 hp 1 phase or 3 phase motor, Magnetic 24 volt switch. Heavy stand, pre set belt tension, one lever belt change 10 gal. pump and tank system Spindle RPM – 2800 Flood coolant – 10 gal tank, 1/3 hp pump, splash guards. Platen – 4″ x 17″, work table 4″ x 6″
  • Model - S660MW • 3 HP, 1 PH or 3 PH, 3450 RPM • 6″ x 60″ wet belt sander, vertical/ horizontal • Steel platen – 6-1/2″ x 17″, 3500 SFPM • Cast iron table with 1/2″ x 1/8″ slot, cast iron frame, Heavy duty base. • Quick belt release, Full safety guard. • Constant spring belt tension, FAST 1 lever belt change !! • Magnetic switch, 24 volts at control • Coolant pump and tank, 10 gal. 1/3 HP
  • ~Additional state sales tax may apply~ Model #BSV-24 Accepts most standard blade widths from .25” to .75”. Offers 4 speeds, ranging from 80 to 318 fpm. Robust 2 hp motor runs on 220-volt single-phase power. Reliable gear-driven transmission saves you from having to replace broken belts or pulleys. Uses tungsten carbide blade guides as well as fully sealed ball bearings for smoothness and durability. Our adjustable blade guide design allows you to get as close as possible to the material for accuracy. We designed this vertical metal cutting band saw to let you cut out the center of the material without having to cut through it. Includes a blade welding station, complete with a shear and grinding wheel, for getting to the middle of a cut or repairing broken blades. Front panels give you easy access for blade alignment. 24” x 22” milled cast iron table pivots 10° front to back and 15° left to right for chamfer cuts. Electro-welded steel plate construction keeps the machine stable, minimizes vibrations, and maintains accuracy. Bright halogen work light helps you see exactly where the cut is. Location:  WI
  • MODEL S6MV • Multi-position, vertical thru horizontal ! 3 HP! Powerful ! • Removable and replaceable steel mesh filter. • Belt sander with heavy-duty enclosed stand and vacuum dust collector. • 6″ x 48″ belt ( same as S6MS). DCV-6 dust collector base, 400 cfm, panel fiter. • Quick one lever abrasive belt changing! • Reversible steel platen , 6″ x14″,cast iron frame
  • Model S660MV • Multi-position, vertical thru horizontal ! 3 HP! Powerful ! • Removable and replaceable steel mesh filter. • Belt sander with heavy-duty enclosed stand and vacuum dust collector. • 6″ x 60″ belt DCV-6 dust collector base, 400 cfm, panel fiter. • Quick one lever abrasive belt changing! • Reversible steel platen , 6″ x14″,cast iron frame
  • • 6″ x 48″ Wet belt sander, 3 hp, 1 ph/220 or 3 ph/220/440 motor, Also available in 50 hz, 575 volt • Magnetic switch with 24 volt at pushbutton. • 3450 rpm motor w/ 2800 SFPM at belt. • Steel reverseable platen 6 1/2″ x 14″ • Multi-postion vertical thru horizontal, cast iron frame. • Cast Iron work table, 6″ x 10″ w/1/2″ x 1/8″ slot • 1 lever quick belt change, pre-set spring belt tension. • Full OSHA guard, heavy duty base • 1/4 hp coolant pump & 10 gal. tank w/ baffles.
  • • S6MS – 6″ x 48″ belt, variable position, direct drive, 1 lever quick belt release !!! • Cast iron frame, Full OSHA safety guard, Heavy duty steel stand. • 3 HP motor 3450 RPM, 1 phase or 3 phase, manual switch, 3500 SFPM • Reversible platen 6 1/2″ x 14″ (S6M) • Cast iron work table 6″ x 10″ with 1/2″ x 1/8″ slot • Option: JIC controls • Shipping dimensions: L 18″ x W 28″ x H32″ • Single phase amp draws: 110V 24 amps and 220V 12 amps. • Three phase amp draws: 220V 8.4 amps and 440V 4.2 amps. • Shipping weight: 230 lbs
  • EQUIPPED WITH: ADJUSTABLE RAKE ANGLE FRONT OPERATED POWER BACK GAUGE FOOT SWITCH BALL TRANSFERS ELECTRICAL: 460V/3PH/60HZ MOTOR: 20 HP  
  • Capacity: Length 12′ / Thickness .250″ Front Operated Power Back Gauge 10′ Squaring Arm Floor Standing 480V 3Ph
  • EQUIPPED WITH HEIDENHAIN 2-AXIS DIGITAL READOUT AUTO CYCLE CONTROLS 25 AMP GENERATOR ASSORTED PIPE GUIDES Location:  PA
  • EQUIPPED WITH: INTERNAL GRINDING SPINDLE (NEEDS TO BE REBUILT) 8" 3-JAW CHUCK FOR WORKHEAD 6" 3-JAW CHUCK FOR WORKHEAD OPERATION & PARTS MANUALS COOLANT SET OF ID SPINDLE ARBORS (8) CENTERS STEADY REST GENERAL SPINDLE CENTER HEIGHT FROM FLOOR: 40" OVERALL HEIGHT: 53.5" FLOOR SPACE REQUIRED: 130" X 71" NET WEIGHT (APPROX): 4,840 LBS SHIPPING WEIGHT (APPROX): 5,686 LBS ELECTRICS: 208 VOLTS, 3 PH, 60 CYC Location:  PA          
  • EQUIPPED WITH: FANUC 18T CNC CONTROL CONTROL GAUGE GLASS SCALES TOUCH PROBE FLAGGING SBS AUTO BALANCER AUTO MACRO CYCLE AUTO PROGRAMMING COOLANT SYSTEM PAPER FILTRATION AUTOMATIC LUBE LOADING JIB (2) WHEELS WITH HUBS
  • GENERAL: DIMENSIONS: 84” LR X 42" FB X 71” H WEIGHT: 2,040 LBS ELECTRICS: 220 VOLTS, 3 PH, 60 CYC FEATURES: • AUTOMATIC VISE OPERATION DURING THE CUTTING CYCLE, SELF CENTERING • FLOOD SYSTEM COOLANT WITH 6 GALLON RESERVOIR • CAST IRON HEAD, HEAD SUPPORT, VISE SUPPORT, VISE JAWS • WELDED STEEL BASE WITH LEVELING SCREW HOLES EQUIPPED WITH: (6) BLADES
  • GENERAL: DIMENSIONS: 7’6” LR X 4’6" FB X 6’6” H WEIGHT: 1,716 LBS ELECTRICS: 440 VOLTS, 3 PH, 60 CYC FEATURES: • HEAD ROTATES UP TO 45° RIGHT OF CENTER FOR MITER CUTTING AND UP TO 90° LEFT OF CENTER FOR MITER CUTTING AND SLOTTING • MINIMUM 6” REMNANT DROP PIECE SIZE FOR MAXIMUM MATERIAL USE • TABLE FEATURES TWO REMOVABLE SURFACE WEAR PLATES TO SUPPORT LONGER CUT LENGTHS • OUTBOARD SECTION OF THE TABLE IS DESIGNED SO SHORTER LENGTHS TUMBLE DOWN A MESH DISCHARGE CHUTE • THREE GIB GUIDES FOR THE CUTTING HEAD WITH TWO ADJUSTABLE CAST IRON GIB BLOCKS IN EACH FOR INCREASED CUTTING ACCURACY AND EASY ADJUSTMENT • MANUAL OILER TO LUBRICATE 1” THICK HARDENED VERTICAL WAYS • REAR SURFACE OF THE GEAR BOX IS MACHINED WITH INTERLOCKING CIRCLES TO EVENLY DISTRIBUTE OIL OVER THE WAYS • 3.5/4.5 HP MOTOR HAS THE MUSCLE TO DRIVE A 14-1/2’ OR 12” BLADE QUICKLY AND QUIETLY THROUGH SOLIDS • LARGE AUTOMATIC CLAMPING VISE FEATURES ADJUSTABLE GIB GUIDES, REMOVABLE FACE PLATES AND AN ANTI-BURR ARM • SELF-ADJUSTING, METAL CHIP BRUSH FILLS REMOVABLE CHIP DRAWER • SELF-ADJUSTING, GRIPPER TYPE FEEDER VISE TRAVELS ON 1-1/2” HARDENED RAILS WITH WIPER RINGS AND WEAR BUSHINGS FOR LONG LIFE • 20” SHUTTLE FEED WITH MULTIPLE STROKES UP TO 99 TIMES, TRAVELS BETWEEN TWO POSITIVE STOPS FOR ACCURATE MATERIAL FEED • SPEED OF FEEDER IS ADJUSTABLE FOR GREATER VERSATILITY • LED AMP METER/BLADE PROTECTION PROTECTS MOTOR BY SHUTTING IT OFF IF IT EXCEEDS PRESENT AMP PEEK • AIR TANK FOR EQUALIZED PRESSURE AND RESERVE IF AIR SOURCE IS INTERRUPTED • AUTOMATIC STOCK SHUT-OFF AND VISUAL INDICATOR LIGHT EQUIPPED WITH: COOLANT
  • Make: Toyota Model: 8FGU25 Year: 2013 Mast: 83/189” Tire: Pneumatic Capacity: 5000 Forks: 42” Meter Hours: 10500 Fuel: LP Attachment: Side shifter
  • Make: Toyota Model: 8FGU25 Year: 2013 Mast: 83/189” Tire: Pneumatic Capacity: 5000 Forks: 42” Meter Hours: 11400 Fuel: LP Attachment: Side shifter
  • TOYOTA 427FG25 5000 LBS LIFT 80 MAX LIFT HEIGHT 58" LOWERED MAST HEIGHT 38" FORK TINES LP GAS UNIT RUNS AND OPERATES WELL Hours: 27500
  • TOYOTA 427FGCU25 5000 LBS CAP 80" MAX HEIGHT 58" LOWERED MAST HEIGHT 38" FORKS, LP GAS, UNIT RUNS AND OPERATES WELL
  • S272V 2 x 72 inch belt grinder & vacuum base The Kalamazoo Industries model S272V 2 x 72 inch belt grinder & vacuum base features 3” and 1-1/2” quick-change contact wheels, plus a platen that rotates 365-degrees. This enables utilization of a single machine for grinding, shaping, contouring, flat work, angles, snagging and roughing. The grinder is mounted on a Kalamazoo Industries heavy-duty DCV-6 dust collector base.
  • The BG214 dual 3 x 132 inch heavy duty backstand grinder other features are easy access design that allows the operator to access the 14” x 3” contact wheel with full left to right movement so they can snag, roughing, contouring, angles and shaping 10HP 3PH 220V or 440V motor, isolation pads, replaceable v-belts. Location:  MI
  • The BG14 backstand grinder is a powerful 10HP 3PH unit with a 70 duro 14″ x 3″ contact wheel. This unit has easy setup, easy backstand tracking, easy clean out, vacuum attachment, magnetic switch, parts table, replaceable parts and isolation pads. The BG14 is great for steel foundries, aggressive grinding, descaling, deburring, and finishing. Location:  MI
  • The Kalamazoo Industries S8W 8 x 60 Inch wet vertical belt sander features a platen work surface of 8″ W x 13″ H and adjustable work table with a work surface of 8″ x 12″ D, 7.5Hp 3PH TEFC motor, air belt tension that requires 40 to 50 PSI, pump and tank system.
  • Standard Equipment: Two Speed Hydraulic Drive Hydraulically powered Lower and Side Bending Roll Adjustment Portable Control Console mounted on Wheels Hydraulic drop end Powered tilting of side bending rolls for cone bending Electronic Digital Readouts to indicate position of both side Bending Rolls
  • Kalamazoo Industries S8HD 8 x 60 inch horizontal belt sander that’s designed for quick heavy duty clean up work on various ferrous and non-ferrous materials. Features air belt tension (air requirements 40 to 50 PSI), 7.5HP motor, easy belt tracking, reversible platen, simple part replacement and 28″ x 10″ work surface.
  • Clausing 20” Drill Press Mechanical Vari-Speed Series 2272 20” Floor, 300-2000 RPM Mechanical Vari-SPD, 3MT, 1 Phase Voltage (115,220) Capacitor Start  - $5,145.00 EVS Series 2274EVS 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 230/3/60 and 220/1/60 Volt  - $ 5,635.00 2272EVS 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 115/1/60 Volt - $6,100.00 CNC Power Feed Series 2279CNC 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 230/3/60 and 220/1/60 Volt w/CNC Power Feed Unit -  $10,110.00 2281CNC 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 115/1/60 Volt w/CNC Power Feed Unit - $10,585.00 Optional Accessories 1897 Key Type Chuck (1898 required) -  $ 165.00 1898 Arbor for 1897  - $25.00 2215-1A-CNC CNC Dual Palm Button Cycle Start Single SPDL -  $995.00 2216 Head Lift Mechanism - $615.00 2293AMT 43” Column in Lieu of Standard 66” - $85.00 2349AMT 90” Column in Lieu of Standard 66” - $215.00 7044 Coolant System for Floor Drill - $480.00 2371MT Mag. Starter Motor 110v Start/Stop Buttons - $1,040.00 (not required if ordering EVS or CNC version) 2377/1MT 1 Speed, 1 Phase Reversing Drum Switch w/ 2371 - $1,385.00 (not required if ordering EVS or CNC version) 302 Start/Stop Foot Switch for Spindle includes 2371MT - $1,155.00 (2272 only) 303E E-Stop Switch (Mag Starter Option Required) - $375.00 (not required if ordering EVS or CNC versions) 7022 Magnetic Base Work Light - $110.00 20-LED 3 Watt 200 Lumen LED Work Light (head installed) - $110.00 Location:  MI
  • Clausing 20” Drill Press Mechanical Vari-Speed Series 2274 20” Floor, 300-2000 RPM Mechanical Vari-SPD, 3MT, 3 Phase Voltage (208,230,460) -  $5,145.00 2275 20” Floor, 200-1300 RPM Mechanical Vari-SPD, 3MT, 3 Phase Voltage (208,230,460) -  $5,145.00 2276 20” Floor, 150-2000 RPM 2 SPD Motor, Mech Vari-SPD 3MT, 230/3/60 - $5,395.00 2277 20” Floor, 150-2000 RPM 2 SPD Motor, Mech Vari-SPD 3MT, 460/3/60 - $5,395.00 EVS Series 2274EVS 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 230/3/60 and 220/1/60 Volt - $5,635.00 2274EVS4 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 460/3/60 Volt - $6,110.00 CNC Power Feed Series 2279CNC 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 230/3/60 and 220/1/60 Volt w/CNC Power Feed Unit - $10,110.00 2280CNC 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 460/3/60 Volt w/CNC Power Feed Unit - $10,585.00 Optional Accessories 1897 Key Type Chuck (1898 required) - $ 165.00 1898 Arbor for 1897 - $25.00 2215-1A-CNC CNC Dual Palm Button Cycle Start Single SPDL - $995.00 2216 Head Lift Mechanism - $615.00 2293AMT 43” Column in Lieu of Standard 66” - $85.00 2349AMT 90” Column in Lieu of Standard 66” - $215.00 7044 Coolant System for Floor Drill - $480.00 2371MT Mag. Starter Motor 110v Start/Stop Buttons - $1,040.00 (not required if ordering EVS or CNC Version) 2375MT 2 Speed Reversing Drum Switch and 2371MT (2276&77 only) - $1,270.00 2377MT Reversing Drum Switch and 2371MT (2274&75 only) - $1,300.00 302 Start/Stop Foot Switch for Spindle includes 2371MT - $1,155.00 (2274&75 only) 302R1 Start/Stop Foot Switch for Spindle, Rev Drum SW, includes 2377 (2274&75 only) - $1,585.00 302R2 Start/Stop Foot Switch for Spindle 2 Spd Drills Rev Drum SW, includes 2375MT (2276&77 only) - $1,585.00 303E E-Stop Switch (Mag Starter Option Required) - $375.00 (not required if ordering EVS or CNC Version) 7022 Magnetic Base Work Light - $110.00 20-LED 3 Watt 200 Lumen LED Work Light (head installed) - $110.00
  • 3.3 cubic ft. U shaped tub rotates media to polish, deburr, peen all types of material. Uses a wide variety of media such as ceramics, steel shot, plastics to achieve mirror finishes on aluminum, steel and most metals. Included coolant tank on the rear of the unit sprays a fine mist into the tub to lubricate the parts and the standard 1 hr. timer can be set for short or long runs without constant attention. The urethane lining lasts for years and can be replaced when needed at the factory.
  • Model No. 7608 Equipped With: Automec CNC 300 Auto Back Gauge Accurpress ETS200 CNC Control Merlin ISB Safety Light Curtain Operator's Control Station Rear Access Safety Cage Foot Pedal Actuator Miscellaneous Dies Operator's Manuals 10-HP Motor 460/3/60 Excellent Condition
  • EQUIPPED WITH: 8" 3-Jaw Power Chuck Fanuc OiTC Control Tailstock Parts Catcher Foot Pedals Manuals RS-232 Flood Coolant Work Light 7/10 HP Main Motor Wired for 3 Phase, 60 Cycle, 220 Volts Overall Size: 104" L-R x 66" F-B x 75" High x 9,500 Lbs.
  • Equipped with: 12 Horse Power Main Motor RAS Multibend CNC Controller Good selection of Dies included. Dimensions (Approximate) L-R x F-B x H 203" x 87.6" x 70" Weight (Approximate) ................ 11,690 lbs
  • Sale!
    EQUIPPED WITH: FANUC 21iTB CONTROL 10 STATION S.ROBO INTEGRATED GANTRY LOADER NORTHFIELD 3-JAW CHUCK MISCELLANEOUS GANG TOOL TOP PLATE TOOL HOLDERS GENERAL FLOOR SPACE REQUIRED: 56" X 68" MACHINE HEIGHT: 76" MACHINE WEIGHT: 3,850 LBS ELECTRICS: 220 VOLTS, 3 PH, 60 CYC YEAR:  2004    
  • Year:  1988 EQUIPPED WITH: 48" CNC BACKGAUGE 12' SQUARING ARM ELECTRIC FOOT SWITCH CONTROL WEIGHT: 28,600 LBS
  • EQUIPPED WITH: Audemi PGP-401 Touch-N-Go Back Gauge Control 48" Back Gauge Sheet Support System 10' Squaring Arm Location:  CA
  • EQUIPPED WITH: Front Operated Powered Back Gauge Ball Transfer Table Electric Foot Pedal 20 Horsepower Location:  CA
  • Equipped With: Quick Blade Gap Adjustment Shadow light line Go to Programmable 36" Back Gauge 3 Front Support Arms Squaring Arm 6' 2 Front Support Arms Quick Blade Gap Adjustment Shadow light line Oil Cooler Location:  TN Year:  1998
  • Equipped With: 36" FRONT OPERATED POWERED BACK GAUGE 2 FRONT ARM SUPPORTS FRONT OPERATED MANUAL RAKE CONTROL.(.002"-.026") FORWARD / REVERSE SINGLE / JOG AND CONTINUOUS MODES 1" x 3" KNIVES Location:  OH