| Equipped With: | |
| · MOTORIZED BACK GAUGE · 30 HP 3/60/220-440v (1770 RPM) WITH CONTROLS · FOOT PEDAL ACTIVATION · 2) EXTENSION ARMS · WITH SQUARING ARMS · MANUAL CENTRALIZED LUBE |
-
-
Equipped With: · CONTROLS MOUNTED ON SHEAR · FOOT PEDAL · 96" SQUARING ARM · (2) 30" SUPPORT ARMS · FRONT OPERATED BACK GAUGE Ships from OH -
Equipped With: - MOTORIZED RAM ADJUSTMENT
- 25 HP, 220/440V, 3/60/1800 RPM W/CONTROLS
- AUTO LUBE
- PALM BUTTONS
-
Equipped With: - FOOT PEDAL
- UP/DOWN BUTTON - ADJ.
- 20 HP 220/442 VOLTS 3 PHASE 1620 RPM MOTOR
-
EQUIPPED WITH:- ROLLER BALL TAKE AWAY TABLE
- BIJUR LUBE
- MOTORIZED RAM ADJUSTMENT
- 9 FLANGES BOLTED TO RAM
- AIR CLUTCH
- MOTOR DRIVE: 7.5 HP, 208-230/460V, 3PH, 60CYC, 1760 RPM WITH CONTROLS
-
EQUIPPED WITH:- MECHANICAL CLUTCH
- 10 HP 230/460 VOLT 3 PHASE
- 1610 RPM MOTOR
-
EQUIPPED WITH:- BACK GAUGE
- FRONT OPERATED
- FOOT PEDAL
- CONTROLS MOUNTED
- SQUARING ARM
- 5 HP 1655 RPM 220/440 VOLT 3 PHASE
- 14.4/6.8 ZMP MOTOR
-
EQUIPPED WITH:- FOOT PEDAL ACTIVATION
- ROLLER BALL BED
- MANUAL SINGLE POINT LUBE
- FOOT PEDAL ACTIVATION
-
EQUIPPED WITH:- HYDRAULIC HOLDDOWN
- POWERED 36" BACK GAUGE WITH DIAL INDICATOR ON FRONT OF MACHINE
-
EQUIPPED WITH:- 11 HOLDDOWNS
- MADISON KIPP HAND CRANK LUBRICATION
- MOTORIZED BACK GAUGE
- FOOT PEDAL ACTIVATION
- MECHANICAL CLUTCH w/AIR ACTIVATION
- MICRO COMPUTER GAUGE CONTROL w/STANDS
- MOTOR DATA: 7-1/2 HP, 3/60/460, 1675 RPM W/CONTROLS
-
-
EQUIPPED WITH:- FOOT TREADLE ACTIVATION
- AUTO BIJUR LUBRICATION SYSTEM
- MANUAL FRONT OPERATED BACK GAUGE 48"
- PUSH BUTTON MOTOR STARTER AND CONTROL
- LIGHT BEAM SHEARING GUIDE
- 5 HP 208-440V, 3 PH, 60 CYC, 1725 RPM MOTOR
-
EQUIPPED WITH:- FOOT PEDAL
- 10' x 8" REMOVABLE FLANGES
- 12' DIE HOLDER & DIE IN LOWER
- GOOD CONDITION
-
EQUIPPED WITH:- Accurite Digital Readouts
- 16" 4 Jaw Chuck
- Steady Rest
- Tail Stock
- 10" 3 jaw chuck, 12" 4 jaw chuck
-
EQUIPPED WITH:- 10” 3 JAW CHUCK
- 10” 4 JAW CHUCK
- 15” FACE PLATE
-
EQUIPPED WITH:- Automec CNC Back Gauge, Model CNC-1000
- 8 ft Die Holder
- Pedestal Stand Foot Pedal w/ Dual Palm Buttons
-
EQUIPPED WITH:- AIR CUSHION
- AIR COUNTERBALANCE
- T-SLOTTED RAM & BOLSTER
-
EQUIPPED WITH:- 15” CHUCK 4 JAW
- 2” SPINDLE HOLE
- INCH/METRIC THREADING
- 15” SWING OVER CROSS SLIDE
- RAPID TRAVERSE
- 4 WAY TOOL HOLDER
- COOLANT
-
-
EQUIPPED WITH:- 36” Front operated power backgauge
- Stroke control
- 36” squaring arm
- Ball transfers in table
- Portable Foot Pedal
- Inch & single stroke mode
- 4 hand clearance pockets
- Full length t-slots in front of tabe
- 4 T-slots F-B in table
- Gap adjustment in bed
- One shot lube system
-
EQUIPPED WITH:- 8’ squaring arm
- Material drop support chute
- Ball transfers in table
- Quick change blade gap adjustment
- Stroke counter 48”
- Front Operated Programmable Backgauge with readout
- Pressure sensing holddowns
- Electric stroke adjustment Shadow light
-
EQUIPPED WITH:- 36” Programmable Backgauge with “Go To” position control, 99 preselect positions, hour meter, stroke control and automatic swing up past 36”
- 10’ squaring arm
- (4) 48” front sheet support arms with scales
- Full length t-slot in front of table
- Extra set of knives
- Oil cooler
- Shadow light and line
- Adjustable stroke length
- Manual quick blade clearance adjustment
- Adjustable stroke length
- 4 edge knives
- 3 position foot switch
- Jog, manual and auto cycle mode
- Ball transfers in table
-
EQUIPPED WITH:- 36" Power Operated Back Gauge w/ LED Readout
- Electric Foot Switch
- New Set of Shear Blades
-
EQUIPPED WITH: NEW DRO FOR BACKGAUGE ELECTRICAL CONTROLS ELECTRIC FOOT PEDALS SHIPS FROM: TN -
EQUIPPED WITH:- FRONT OPERATED POWER BACKGUAGE
- FLOOR STANDING
- FOOT PEDAL
-
EQUIPPED WITH:- Hurco Autobend & CNC Back Gauge 2 Axis
- Euro and American Top Die Holders
- Bottom Die Holder
- Light Curtain
-
-
EQUIPPED WITH:- 4-Way Tooling
- 30" 4-Jaw Chuck
- 24" 3-Jaw Chuck
-
EQUIPPED WITH:- Newall Digital Readout
- Includes tailstock (not in picture)
-
EQUIPPED WITH:- AUTOMEC CNC 150 SINGLE AXIS BACK GAUGE
- PALM BUTTON/FOOT SWITCH
-
EQUIPPED WITH:- CONTROL
- PALM BUTTON STATION
- FLOOR STANDING
-
EQUIPPED WITH:- DRC SINGLE AXIS PROGRAMMABLE BACK GAUGE
- TWO SPEED RAM
- FOOT PEDAL & PALM BUTTONS
-
EQUIPPED WITH:- Control Panel on Column
- Hydraulic Drop End
- Adjustable Rolls for Cone Rolling
-
EQUIPPED WITH:- 2-Axis DRO
- Steady Rest
- Taper Attachment
- 8" 3-Jaw Chuck
-
EQUIPPED WITH:- PC-100 CNC Back Guage
- Pnuematic Sheet Supports
- Squaring Arm
- (2) Support Arms
-
EQUIPPED WITH:- Front operated power back gauge; Squaring arm; Blade guard
-
EQUIPPED WITH:- 36" FRONT OPERATED PROGRAMMABLE POWER BACK GAUGE
- ACCUSHEAR CNC FRONT GAUGING SYSTEM W/10' ACCUSHEAR
- CNC SQUARING GAGE AND (2) 5' SUPPORT ARMS &
- AUTOMEC CNC CONTROL
- (16) HYDRAULIC HOLDDOWNS
- FOOT SWITCH
- NO PIT REQUIRED
-
EQUIPPED WITH:- PROFESSIONAL 3 CNC CONTROL
- 217 PSI COOLANT THRU SPINDLE
- CHIP CONVEYOR
- (2) PALLET APC
-
YEAR 2002 MODEL H4F 600T -
-
EQUIPPED WITH:- Cincinnati 2-Axis CNC Control
- Back Gauge (X-24", R-8")
- 6' Lower Die Holder
- Electric Foot Switch
-
EQUIPPED WITH:- PALM BUTTONS
- LIGHT CURTAINS
- FOOT PEDAL
- LINCOLN LUBRICATOR
- FINE TILT
- NO BACK GAUGE
-
EQUIPPED WITH:- ELECTRIC FOOT SWITCH
- HURCO AUTOBEND 7 CNC BACK GAUGE
- GOOD CONDITION
-
EQUIPPED WITH:- 25" DI-ACRO CNC GAUGING SYSTEMS
- TONNAGE CONTROL WITH GAUGE
- ADJUSTABLE PRESSURE CONTROL
- SELF CONTAINED HYDRAULIC SYSTEM
- ELECTRIC FOOT SWITCH OPERATION
- GOOD CONDITION
-
EQUIPPED WITH:- Under power on our floor!!
- Hurco Autobend 7 CNC back gauge
- Banner Safety light curtains & 2-operator control system
- Can be set for operation by (1) or (2) operators
- (2) Dual palm button pedestal control stands
- (2) Foot pedal controls
-
EQUIPPED WITH:- Cyblec 3 axis CNC control
- X control
- Y1, Y2 control
- R control
- crowning control
- Power clamp ram
- Wila Crowning attachment
-
EQUIPPED WITH:- Automec CNC 99 2-axis control includes storage for 99 jobs with up to 30 bends per job
- backgauge retract, Inch / metric programming, Manual / automatic operating modes and
- Tonnage control
- Portable foot pedal
- Full length die holder
- Inch / single stroke mode
- Lubrication system
-
EQUIPPED WITH:- Hurco Autobend 7, 2 axis CNC control with memory for 600 programs and 2,400 bends. Tool library for 45 punches and dies, RS232 interface & Programmable retract.
- Portable foot pedal
- Full length die holder
- 3 position ram control
- Tonnage control
-
EQUIPPED WITH:- 176 Ton x 12' capacity
- Delem DA 56s 4 axis control + crowning
- Fiessler laser light curtain
- Chrome molly 4 sided die and gooseneck punch
-
EQUIPPED WITH:- THREE SPEED HYDRAULIC POWER UNIT
- FINE TILT ADJUSTMENT
- PALM BUTTON CONTROLS