- HYDRAULIC OVERLOAD PROTECTION
- (2) AIR COUNTERBALANCE CYLINDERS TO SLIDE
- STROKE POSITION INDICATOR
- AC MAIN DRIVE MOTOR
- ELECTRICAL CONTROLS
-
EQUIPPED WITH: -
EQUIPPED WITH:- ADAPTIVE AUTO FORM 5-AXIS COMPUTERIZED GAUGING
- LIGHT CURTAIN
- 4-WAY LOWER DIE (1", 1-12", 2" , 2-1/2" OPENINGS)
- NO PIT REQUIRED
- CROWNING
-
EQUIPPED WITH:- SP-U10L CNC CONTROL
- 10" 3 JAW HYDRAULIC CHUCK
- PARTS CATCHER
- PROGRAMMABLE TAILSTOCK
- CHIP CONVEYOR
- COOLANT SYSTEM
-
EQUIPPED WITH:- Double acting work head
- 44” between uprights
- 8-1/4” width between table channels
- (2) forged steel V-blocks
- Flat ram nose
- Pressure gauge
- Manual cable lift with locking pins
- Variable speed ram
- 10 quart oil capacity
-
EQUIPPED WITH:- Frame
- Cylinder
- Two Forged Steel Table Plates
- Pressure Guage
- Lifting Chain
- Controls-On/Off switch with Joystick Hydraulic Control
- Hydraulic Pump-Combination Power Unit
- Oil Capacity- Approx 3 Gallons (US)
-
EQUIPPED WITH:- Fanuc 16i-MB CNC Control,
- 17" x 32" 360 Degree Rotating Worktable,
- 40 Station Automatic Tool Changer,
- Spindle Chiller,
- Chip Conveyor,
- Coolant Filtration System,
- German Quality Built Machine.
-
EQUIPPED WITH:- CONTROLS
- FOOT PEDAL ACTIVATION
- 2) EXTENSION ARMS
- SQUARING ARMS
- MANUAL CENTRALIZED LUBE
-
EQUIPPED WITH:- 36" Front Operated Power Back Gauge w/Digital LED Display
- Swing Up Back Gauge
- 3 Position Foot Switch
- Manual Quick Blade Clearance
- Autogage Programmable Front Gauge
- 4 Edge Blades
-
EQUIPPED WITH:- Wysong PC100 Back Gage Controller with Single and Repeat Cycles
- New Electric Foot Pedal Trip Control
- (2) Adjustable 31" Long Front Material Support Arms
- (1) 63" Long Squaring Arm (On Left Side) with (2) Adjustable Material Stops
- Bijur Pressurized Lubrication System
- Adjustable & Replaceable Ram Ways Wear Strips
- Full Length Finger Guard
- Mechanical Material Hold Downs
- (6) Ball Type Material Supports Built in the Table
- Manually Adjustable Cycle Brake
- Overhead Light Bar with (3) Flood Lights
- Air Actuated Mechanical Clutch – Compressed Air Required
- Heavy Duty Pattern Machine, Flush Floor Design
- 15 HP Main Motor, 230/460 Volts, 1760 RPM
- 1/2 HP Back Gage Motor, 230/460 Volts
- Wired for 3 Phase, 60 Hz, 230/460 Volts
- Presently Wired for 440 Volt Operation
- This Machine is in Very Good Physical and Running Condition
-
SHIPS FROM: TX -
EQUIPPED WITH:- SQUARING ARM & (1) SUPPORT ARM
- FRONT OPERATED POWER BACK GAUGE
- HYDRAULIC & ELECTRICAL CONTROLS
- REMOTE FOOT PEDAL
-
-
EQUIPPED WITH:- NEW rolling pedestal control includes:
- (4) New joystick controls
- (4) New digital roll position indicators
- New Quick disconnect
- New Emergency stop button
- New Push/Pull style Stop/Start button
- NEW wire encoders for roll positioning
- NEW Emergency stop safety switches & cables - front and back
- Emergency stop buttons on machine - front and back
- Seals & hoses replaced as needed
- NEW rolling pedestal control includes:
-
EQUIPPED WITH:- POWER BACK GAUGE
- SQUARING ARM
-
EQUIPPED WITH:- 2-Axis Hurco Autobend 5C CNC back gauge & control
-
EQUIPPED WITH:- Air operated drop end
- Forming roll geared
- Power adjustment on forming roll
- Forming and pinch rolls grooved longitudinally
-
EQUIPPED WITH:- Front operated power back gauge
- Squaring arm
- Support arms
- Spare set of blades
- Foot pedal
-
EQUIPPED WITH:- 2-axis CNC control and back gauge
- Microguard light curtains
-
EQUIPPED WITH:- Initial Pinch Configuration
- Power Drop End
- Power Roll Adjustment
- Roll Position Indicator
- NEW emergency stop safety switch and cable
- NEW forward-reverse handheld pendant control
-
SHIPS FROM: AR -
SHIPS FROM: OH -
EQUIPPED WITH:- Mitsubishi Meldas 500M CNC Controls,
- Renashaw Probing,
- 26' x 72" Planer Table,
- Right Angle Head,
- Coolant System,
- 5 KVA Transformer
-
EQUIPPED WITH:- FANUC 31I-MODEL B CNC CONTROL
- TOOL PROBE
- COOLANT THRU SPINDLE
- SPINDLE CHILLER
- CHIP CONVEYOR
- T-SLOTTED TABLE
- ALL AVAILABLE MANUALS
-
EQUIPPED WITH:- Accurpress AP2 X,Y CNC Control, Manual Z
- ETS pedestal
- Die Rail
-
EQUIPPED WITH:- HURCO AUTOBEND #7 CNC BACKGAUGE
- TONNAGE CONTROL
- REMOTE FOOT PEDAL