• The BG214 dual 3 x 132 inch heavy duty backstand grinder other features are easy access design that allows the operator to access the 14” x 3” contact wheel with full left to right movement so they can snag, roughing, contouring, angles and shaping 10HP 3PH 220V or 440V motor, isolation pads, replaceable v-belts. Location:  MI
  • The BG14 backstand grinder is a powerful 10HP 3PH unit with a 70 duro 14″ x 3″ contact wheel. This unit has easy setup, easy backstand tracking, easy clean out, vacuum attachment, magnetic switch, parts table, replaceable parts and isolation pads. The BG14 is great for steel foundries, aggressive grinding, descaling, deburring, and finishing. Location:  MI
  • The Kalamazoo Industries S8W 8 x 60 Inch wet vertical belt sander features a platen work surface of 8″ W x 13″ H and adjustable work table with a work surface of 8″ x 12″ D, 7.5Hp 3PH TEFC motor, air belt tension that requires 40 to 50 PSI, pump and tank system.
  • Standard Equipment: Two Speed Hydraulic Drive Hydraulically powered Lower and Side Bending Roll Adjustment Portable Control Console mounted on Wheels Hydraulic drop end Powered tilting of side bending rolls for cone bending Electronic Digital Readouts to indicate position of both side Bending Rolls
  • Kalamazoo Industries S8HD 8 x 60 inch horizontal belt sander that’s designed for quick heavy duty clean up work on various ferrous and non-ferrous materials. Features air belt tension (air requirements 40 to 50 PSI), 7.5HP motor, easy belt tracking, reversible platen, simple part replacement and 28″ x 10″ work surface.
  • Clausing 20” Drill Press Mechanical Vari-Speed Series 2272 20” Floor, 300-2000 RPM Mechanical Vari-SPD, 3MT, 1 Phase Voltage (115,220) Capacitor Start  - $5,145.00 EVS Series 2274EVS 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 230/3/60 and 220/1/60 Volt  - $ 5,635.00 2272EVS 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 115/1/60 Volt - $6,100.00 CNC Power Feed Series 2279CNC 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 230/3/60 and 220/1/60 Volt w/CNC Power Feed Unit -  $10,110.00 2281CNC 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 115/1/60 Volt w/CNC Power Feed Unit - $10,585.00 Optional Accessories 1897 Key Type Chuck (1898 required) -  $ 165.00 1898 Arbor for 1897  - $25.00 2215-1A-CNC CNC Dual Palm Button Cycle Start Single SPDL -  $995.00 2216 Head Lift Mechanism - $615.00 2293AMT 43” Column in Lieu of Standard 66” - $85.00 2349AMT 90” Column in Lieu of Standard 66” - $215.00 7044 Coolant System for Floor Drill - $480.00 2371MT Mag. Starter Motor 110v Start/Stop Buttons - $1,040.00 (not required if ordering EVS or CNC version) 2377/1MT 1 Speed, 1 Phase Reversing Drum Switch w/ 2371 - $1,385.00 (not required if ordering EVS or CNC version) 302 Start/Stop Foot Switch for Spindle includes 2371MT - $1,155.00 (2272 only) 303E E-Stop Switch (Mag Starter Option Required) - $375.00 (not required if ordering EVS or CNC versions) 7022 Magnetic Base Work Light - $110.00 20-LED 3 Watt 200 Lumen LED Work Light (head installed) - $110.00 Location:  MI
  • Clausing 20” Drill Press Mechanical Vari-Speed Series 2274 20” Floor, 300-2000 RPM Mechanical Vari-SPD, 3MT, 3 Phase Voltage (208,230,460) -  $5,145.00 2275 20” Floor, 200-1300 RPM Mechanical Vari-SPD, 3MT, 3 Phase Voltage (208,230,460) -  $5,145.00 2276 20” Floor, 150-2000 RPM 2 SPD Motor, Mech Vari-SPD 3MT, 230/3/60 - $5,395.00 2277 20” Floor, 150-2000 RPM 2 SPD Motor, Mech Vari-SPD 3MT, 460/3/60 - $5,395.00 EVS Series 2274EVS 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 230/3/60 and 220/1/60 Volt - $5,635.00 2274EVS4 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 460/3/60 Volt - $6,110.00 CNC Power Feed Series 2279CNC 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 230/3/60 and 220/1/60 Volt w/CNC Power Feed Unit - $10,110.00 2280CNC 20” Floor, 50-2000 RPM, Electronic Vari-SPD, 3MT 460/3/60 Volt w/CNC Power Feed Unit - $10,585.00 Optional Accessories 1897 Key Type Chuck (1898 required) - $ 165.00 1898 Arbor for 1897 - $25.00 2215-1A-CNC CNC Dual Palm Button Cycle Start Single SPDL - $995.00 2216 Head Lift Mechanism - $615.00 2293AMT 43” Column in Lieu of Standard 66” - $85.00 2349AMT 90” Column in Lieu of Standard 66” - $215.00 7044 Coolant System for Floor Drill - $480.00 2371MT Mag. Starter Motor 110v Start/Stop Buttons - $1,040.00 (not required if ordering EVS or CNC Version) 2375MT 2 Speed Reversing Drum Switch and 2371MT (2276&77 only) - $1,270.00 2377MT Reversing Drum Switch and 2371MT (2274&75 only) - $1,300.00 302 Start/Stop Foot Switch for Spindle includes 2371MT - $1,155.00 (2274&75 only) 302R1 Start/Stop Foot Switch for Spindle, Rev Drum SW, includes 2377 (2274&75 only) - $1,585.00 302R2 Start/Stop Foot Switch for Spindle 2 Spd Drills Rev Drum SW, includes 2375MT (2276&77 only) - $1,585.00 303E E-Stop Switch (Mag Starter Option Required) - $375.00 (not required if ordering EVS or CNC Version) 7022 Magnetic Base Work Light - $110.00 20-LED 3 Watt 200 Lumen LED Work Light (head installed) - $110.00
  • 3.3 cubic ft. U shaped tub rotates media to polish, deburr, peen all types of material. Uses a wide variety of media such as ceramics, steel shot, plastics to achieve mirror finishes on aluminum, steel and most metals. Included coolant tank on the rear of the unit sprays a fine mist into the tub to lubricate the parts and the standard 1 hr. timer can be set for short or long runs without constant attention. The urethane lining lasts for years and can be replaced when needed at the factory.
  • Model No. 7608 Equipped With: Automec CNC 300 Auto Back Gauge Accurpress ETS200 CNC Control Merlin ISB Safety Light Curtain Operator's Control Station Rear Access Safety Cage Foot Pedal Actuator Miscellaneous Dies Operator's Manuals 10-HP Motor 460/3/60 Excellent Condition
  • EQUIPPED WITH: 8" 3-Jaw Power Chuck Fanuc OiTC Control Tailstock Parts Catcher Foot Pedals Manuals RS-232 Flood Coolant Work Light 7/10 HP Main Motor Wired for 3 Phase, 60 Cycle, 220 Volts Overall Size: 104" L-R x 66" F-B x 75" High x 9,500 Lbs.
  • Equipped with: 12 Horse Power Main Motor RAS Multibend CNC Controller Good selection of Dies included. Dimensions (Approximate) L-R x F-B x H 203" x 87.6" x 70" Weight (Approximate) ................ 11,690 lbs
  • Year:  1988 EQUIPPED WITH: 48" CNC BACKGAUGE 12' SQUARING ARM ELECTRIC FOOT SWITCH CONTROL WEIGHT: 28,600 LBS
  • EQUIPPED WITH: Audemi PGP-401 Touch-N-Go Back Gauge Control 48" Back Gauge Sheet Support System 10' Squaring Arm Location:  CA
  • EQUIPPED WITH: Front Operated Powered Back Gauge Ball Transfer Table Electric Foot Pedal 20 Horsepower Location:  CA
  • Equipped With: Quick Blade Gap Adjustment Shadow light line Go to Programmable 36" Back Gauge 3 Front Support Arms Squaring Arm 6' 2 Front Support Arms Quick Blade Gap Adjustment Shadow light line Oil Cooler Location:  TN Year:  1998
  • Equipped With: 36" FRONT OPERATED POWERED BACK GAUGE 2 FRONT ARM SUPPORTS FRONT OPERATED MANUAL RAKE CONTROL.(.002"-.026") FORWARD / REVERSE SINGLE / JOG AND CONTINUOUS MODES 1" x 3" KNIVES Location:  OH
  • Equipped With: Flush Floor Mounted Hurco Autobend 7 CNC Back Gauge Manual Crowning Die Holder Light Curtains Palm Buttons Floor Electric Foot Control Location:  MD
  • Yr:  1964 Equipped With: - 24" Rear Operated Manual Back Gauge - 4' Squaring Arm - Full Length Foot Treadle
  • EQUIPPED WITH: FRONT OPERATED POWER BACK GAUGE FRONT SUPPORT ARM SQUARING ARM FOOT PEDAL Location:  NJ
  • EQUIPPED WITH: - FRONT OPERATED POWER BACK GAUGE WITH FINE WHEEL ADJUSTMENT - FOOT PEDAL - BIJUR LUBRICATION SYSTEM Location:  NJ
  • Equipped With: S2 SERIES 2-POINT STRAIGHT SIDE PRESSThe Stamtec S2 two-point straight side press (a.k.a. double crank press) is designed for stamping large parts or ones that require a large bed area to accommodate progressive or transfer dies. Oftentimes, these types of operations require high tonnage, high flywheel energy, maximum frame or bed rigidity, or some combination thereof. The path of the slide is guided by eight full-length, ninety-degree gibs with nickel-bronze wear plates, offering maximum control, a high degree of accuracy and ease of adjustment. Location:  OH
  • Model Hydracrop 50SD Includes: Gauge Tables- Punch and Coper Notcher Station Electric Foot Switches Location:  NY
  • STANDARD EQUIPMENT INCLUDES: 9" PUNCH THROAT, MANUAL PUNCH ALIGNER, 4 WAY-24" LOW RAKE FLAT BAR SHEAR BLADES, ELECTRIC FOOT CONTROL, 2-1/4" STRIPPER, - L, 150 & 500 SERIES PUNCH & DIE ADAPTOR KIT THAT ACCEPTS UP TO 2-1/4" DIA PUNCHING VARIABLE ELECTRIC STROKE CONTROL, FLAT BAR SHEAR TABLE, GREASE BANK, CHOICE OF NOTCHER IN 4TH STATION; OF A PIPE, SQUARE OR V COPER NOTCHER PRICE DOES NOT INCLUDE ANGLE SHEAR BLADES 7-1/2 H.P. 3 PHASE 220/480 VOLT MOTOR ALSO AVAILABLE: SAME AS ABOVE, 7-1/2 H.P., 1 PHASE, 220 VOLT MOTOR Location:  MN
  • STANDARD EQUIPMENT INCLUDES: 9" PUNCH THROAT,MANUAL PUNCH ALIGNER, 4 WAY-24" LOW RAKE FLAT BAR SHEAR BLADES, ELECTRIC FOOT CONTROL, 2-1/4" STRIPPER, - L, 150 & 500 SERIES PUNCH & DIE ADAPTOR KIT THAT ACCEPTS UP TO 2-1/4" DIA PUNCHING VARIABLE ELECTRIC STROKE CONTROL, FLAT BAR SHEAR TABLE, GREASE BANK,PRICE DOES NOT INCLUDE ANGLE SHEAR BLADES 7-1/2 H.P. 3 PHASE 220/480 VOLT MOTOR ALSO AVAILABLE: SAME AS ABOVE 7-1/2 H.P. 1 PHASE 220 VOLT MOTOR Location:  MN  
  • STANDARD EQUIPMENT: 9" PUNCH THROAT, MANUAL PUNCH ALIGNER, 4 WAY-24" LOW RAKE FLAT BAR SHEAR BLADES, ELECTRIC FOOT CONTROL, 2-1/4" STRIPPER, - L, 150 & 500 SERIES PUNCH & DIE ADAPTOR KIT THAT ACCEPTS UP TO 2-1/4" DIA PUNCHING VARIABLE ELECTRIC STROKE CONTROL, FLAT BAR SHEAR TABLE, GREASE BANK, PRICE DOES NOT INCLUDE ANGLE SHEAR BLADES Also Available:  7-1/2 H.P. 1 PHASE 220 VOLT MOTOR