- PC-100 CNC Back Guage
- Pnuematic Sheet Supports
- Squaring Arm
- (2) Support Arms
-
EQUIPPED WITH: -
EQUIPPED WITH:- 2-Axis DRO
- Steady Rest
- Taper Attachment
- 8" 3-Jaw Chuck
-
EQUIPPED WITH:- Control Panel on Column
- Hydraulic Drop End
- Adjustable Rolls for Cone Rolling
-
EQUIPPED WITH:- DRC SINGLE AXIS PROGRAMMABLE BACK GAUGE
- TWO SPEED RAM
- FOOT PEDAL & PALM BUTTONS
-
EQUIPPED WITH:- CONTROL
- PALM BUTTON STATION
- FLOOR STANDING
-
EQUIPPED WITH:- AUTOMEC CNC 150 SINGLE AXIS BACK GAUGE
- PALM BUTTON/FOOT SWITCH
-
EQUIPPED WITH:- Newall Digital Readout
- Includes tailstock (not in picture)
-
EQUIPPED WITH:- 4-Way Tooling
- 30" 4-Jaw Chuck
- 24" 3-Jaw Chuck
-
-
EQUIPPED WITH:- Hurco Autobend & CNC Back Gauge 2 Axis
- Euro and American Top Die Holders
- Bottom Die Holder
- Light Curtain
-
EQUIPPED WITH:- FRONT OPERATED POWER BACKGUAGE
- FLOOR STANDING
- FOOT PEDAL
-
EQUIPPED WITH: NEW DRO FOR BACKGAUGE ELECTRICAL CONTROLS ELECTRIC FOOT PEDALS SHIPS FROM: TN -
EQUIPPED WITH:- 36" Power Operated Back Gauge w/ LED Readout
- Electric Foot Switch
- New Set of Shear Blades
-
EQUIPPED WITH:- 36” Programmable Backgauge with “Go To” position control, 99 preselect positions, hour meter, stroke control and automatic swing up past 36”
- 10’ squaring arm
- (4) 48” front sheet support arms with scales
- Full length t-slot in front of table
- Extra set of knives
- Oil cooler
- Shadow light and line
- Adjustable stroke length
- Manual quick blade clearance adjustment
- Adjustable stroke length
- 4 edge knives
- 3 position foot switch
- Jog, manual and auto cycle mode
- Ball transfers in table
-
EQUIPPED WITH:- 8’ squaring arm
- Material drop support chute
- Ball transfers in table
- Quick change blade gap adjustment
- Stroke counter 48”
- Front Operated Programmable Backgauge with readout
- Pressure sensing holddowns
- Electric stroke adjustment Shadow light
-
EQUIPPED WITH:- 36” Front operated power backgauge
- Stroke control
- 36” squaring arm
- Ball transfers in table
- Portable Foot Pedal
- Inch & single stroke mode
- 4 hand clearance pockets
- Full length t-slots in front of tabe
- 4 T-slots F-B in table
- Gap adjustment in bed
- One shot lube system
-
-
EQUIPPED WITH:- 15” CHUCK 4 JAW
- 2” SPINDLE HOLE
- INCH/METRIC THREADING
- 15” SWING OVER CROSS SLIDE
- RAPID TRAVERSE
- 4 WAY TOOL HOLDER
- COOLANT
-
EQUIPPED WITH:- 10” 3 JAW CHUCK
- 10” 4 JAW CHUCK
- 15” FACE PLATE
-
EQUIPPED WITH:- Automec CNC Back Gauge, Model CNC-1000
- 8 ft Die Holder
- Pedestal Stand Foot Pedal w/ Dual Palm Buttons
-
EQUIPPED WITH:- Accurite Digital Readouts
- 16" 4 Jaw Chuck
- Steady Rest
- Tail Stock
- 10" 3 jaw chuck, 12" 4 jaw chuck
-
EQUIPPED WITH:- FOOT PEDAL
- 10' x 8" REMOVABLE FLANGES
- 12' DIE HOLDER & DIE IN LOWER
- GOOD CONDITION
-
EQUIPPED WITH:- FOOT TREADLE ACTIVATION
- AUTO BIJUR LUBRICATION SYSTEM
- MANUAL FRONT OPERATED BACK GAUGE 48"
- PUSH BUTTON MOTOR STARTER AND CONTROL
- LIGHT BEAM SHEARING GUIDE
- 5 HP 208-440V, 3 PH, 60 CYC, 1725 RPM MOTOR
-
-
EQUIPPED WITH:- 11 HOLDDOWNS
- MADISON KIPP HAND CRANK LUBRICATION
- MOTORIZED BACK GAUGE
- FOOT PEDAL ACTIVATION
- MECHANICAL CLUTCH w/AIR ACTIVATION
- MICRO COMPUTER GAUGE CONTROL w/STANDS
- MOTOR DATA: 7-1/2 HP, 3/60/460, 1675 RPM W/CONTROLS